Sensor Instruments
Entwicklungs- und Vertriebs GmbH
Schlinding 15
D-94169 Thurmansbang
Telefon +49 8544 9719-0
Telefax +49 8544 9719-13
info@sensorinstruments.de

Praktische Beispiele aus dem industriellen Einsatz
SPECTRO-3-FIO-UV


1) Sprache auswählen:


Automotive Industry (Automobilindustrie) 
N° 559


Controllo della presenza di uno strato fluorescente su una guarnizione in gomma
Si deve monitorare la presenza di uno strato fluorescente su una guarnizione di gomma.

Presence control of fluorescent coating
The presence of a fluorescent coating on rubber seal should be controlled.
Textile Industry (Textilindustrie) 
N° 516


Controllo della presenza di fili fluorescenti in un pannolino in fase di produzione
Si deve monitorre la presenza di fili fluorescenti all’interno di pannolini.

Fluorescent thread presence control in diapers during the production
The presence of fluorescent threads in diapers should be inline controlled.
Paper Industry / Printing Industry (Papierindustrie / Druckindustrie) 
N° 493


Rilevamento della fluorescenza di fogli metallici
Si deve monitorare la presenza di uno strato fluorescente su fogli metallici.

Fluorescence detection on metal foils
The presence of fluorescence coating on a metal foil should be controlled.
Machine Building / Metal-working Industry (Maschinenbau / Metallverarbeitung) 
N° 474


Rilevare olio fluorescente su diversi anelli di tenuta
Si deve controllare la presenza di olio su anelli di tenuta. Tenere presente che l’olio diventa fluorescente se si utilizza luce UV.

Detection of fluorescent oil on flat washers
The presence of oil on different flat washers should be controlled. It has to be taken into account, that the oil is fluorescent, if UV light is used.
Machine Building / Metal-working Industry (Maschinenbau / Metallverarbeitung) 
N° 473


Rilevare un lubrificante fluorescente su aste in metallo
Si deve monitorare la presenza di uno strato lubrificante fluorescente sotto l’influsso di luce UV.

Detection of fluorescent lubricant on metal pins
Fluorescent lubricant should be detected on metal pins.
Machine Building / Metal-working Industry (Maschinenbau / Metallverarbeitung) 
N° 456


Rilevamento di adesivo su filetto di vite
Si deve controllare la presenza e la quantità di adesivo fluorescente (sotto effetto di luce UV) sul filetto di una vite.

Glue detection on the thread of a screw
The presence and amount of fluorescent (fluorescent under the influence of UV light) glue on the thread of a screw should be detected.
Machine Building / Metal-working Industry (Maschinenbau / Metallverarbeitung) 
Automotive Industry (Automobilindustrie) 
N° 424


Controllo della presenza di goccia d’olio su una superficie di acciaio
Su una superficie di acciaio si deve monitorare la presenza di una goccia d’olio.

Oil drop presence control on a steel surface
The presence of an oil drop on a steel surface should be controlled.
Packaging Industry (Verpackungsindustrie) 
N° 421


Rilevamento di uno strato di adesivo fluorescente su una busta in plastica
Su una busta di plastica si deve riconoscere uno strato adesivo fluorescente sotto influsso UV. Tenere presente che lo strato adesivo è coperto da un nastro di plastica trasparente.

Fluorescent glue strip detection on a plastic bag
A glue strip, which becomes fluorescent in the presence of UV light, should be detected on a plastic bag. At this, the glue strip is covered with a transparent plastic film.
Paper Industry / Printing Industry (Papierindustrie / Druckindustrie) 
Pharmacy (Pharmazie) 
N° 417


Rilevamento di etichette fluorescenti
Si devono rilevare etichette fluorescenti sotto effetto di luce UV e vuoti tra le etichette.

Fluorescent label detection
Fluorescent labels should be detected on semitransparent carriers.
Synthetic Industry (Kunststoffindustrie) 
Packaging Industry (Verpackungsindustrie) 
N° 330


Rilevare un’etichetta fluorescente trasparente su materiale di supporto trasparente
Si deve rilevare un’etichetta di plastica trasparente su un nastro metallico trasparente. L’etichetta diventa fluorescente per effetto della luce UV.

Detection of a transparent fluorescent label on transparent plastic film
A transparent plastic label should be detected on a transparent plastic film. It should be taken into account, that the label is fluorescent in using UV-light.
Packaging Industry (Verpackungsindustrie) 
N° 317


Rilevamento di striscia fluorescente su ticket
Si deve rilevare una striscia fluorescente per effetto di luce UV.

Fluorescent color stripe detection on tickets
A fluorescent color stripe on a ticket should be detected.
Chemical Industry (Chemische Industrie) 
N° 195


Differenziazione colore dell'olio fluorescente
Dovrebbero essere differenziati i diversi tipi di olio che vengono utilizzati per i motori. Viene utilizzato l'effetto naturale della fluorescenza UV di olio minerale. Inoltre il liquido fluorescente sarà aggiunto ad alcuni oli minerali, che permette una maggiore distinzione.

Color differentiation of fluorescent oil
Different oil types which are used for engines should be differentiated. At this, the natural effect of UV fluorescence of mineral oil is used. Furthermore fluorescent liquid will be added to some of the mineral oils, which allows a differentiation of the adequate types.
Automotive Industry (Automobilindustrie) 
N° 152


Rilevamento di colla fluorescente secca su un'asta
Su un'asta la colla fluorescente è usata per sigillare l'intersezione tra l'asta e il rullo.

Detection of fluorescent cured glue on a shaft
On a shaft fluorescent glue is used to seal the intersection between the shaft and a roll.
Pharmacy (Pharmazie) 
N° 116


Controllo della presenza della spatola in una scatola farmaceutica
Deve essere controllata la presenza di una spatola fluorescente in una scatola farmaceutica. Durante le prove il lato anteriore è aperto.

Control of the presence of the spatula in a pharmaceutical box
The presence of a fluorescent spatula in a pharmaceutical box should be checked. During the tests the front side is open.
Environmental Technology (Umwelttechnik) 
N° 98


Rilevamento delle acque di scarico olio
Deve essere controllata la quantità di olio in acqua reflue. I valori tipici sono 500 ppm di olio nel flusso delle acque reflue e l'obiettivo è di raggiungere i 100 ppm. Per verificare questo può essere utilizzato l'effetto fluorescente.

Oil containing waste water detection
On an oil press the amount of oil in the waste water must be controlled. Typical values are 500ppm of flux oil in the waste water and the goal is to reach the 100ppm. At this the fluorescent effect of the flux oil can be used.
Machine Building / Metal-working Industry (Maschinenbau / Metallverarbeitung) 
Construction Industry / Ceramic-finish Industry (Bauindustrie / Keramikverarbeitung) 
Furniture Industry / Wood-working Industry (Möbelindustrie / Holzindustrie) 
N° 88


Controllo della colla fluorescente sul nastro abrasivo
Durante la produzione di nastro abrasivo con una striscia di colla larga 10 mm deve essere rilevata la presenza della colla fluorescente. I difetti maggiori a 2 mm di lunghezza devono essere rilevati. La distanza della testa sensore dall'oggetto dovrebbe essere di circa 20 mm e la gamma di rilevazione circa 2 mm x 10 mm.

Fluorescent glue control on an abrasive belt
During the production of abrasive belt material with a 10mm wide glue stripe the presence of the fluorescent glue must be observed. Defects greater than 2mm in length must be proper detected. The distance of the sensor head to the object should be approximately 20mm and the detecting range around 2mm x 10mm.
Furniture Industry / Wood-working Industry (Möbelindustrie / Holzindustrie) 
N° 47


Rilevamento del colore dei segni fluorescenti sui pannelli di legno
I nodi nelle tavole di legno sono contrassegnati con un colore fluorescente. Il segno fluorescente ha normalmente una larghezza di 15 mm, e può accadere che vengano applicate due linee di questa larghezza disposte ad una distanza di 20 mm fra loro. Inoltre i marchi fluorescenti dovrebbero essere rilevati ad una distanza di 200 mm, deve essere rilevato anche il segno con larghezza di 5mm.

Color detection of fluorescent marks on wood plates
On wooden plates defects will be marked with a fluorescent marker. The fluorescent mark has normally a width of about 15mm and it can happen, that two of this marks lie 20 mm away of each other, but must be detected as two separate marks. Furthermore the fluorescent marks should be detected at a distance of 200 mm to the object and even a mark with a width of 5mm should be detected.


AKTUELLES

Messeteilnahmen:

 •   AIMEX Automation World 2024
 •   IFAT Munich 2024
 •   FIP 2024
 •   PRS Europe 2024
 •   SKZ-Innovationstag Recycling
 •   SKZ-Netzwerktag
 •   SKZ-Technologietag
 •   PRS Middle East & Africa 2024
 •   Plastics Recycling World Expo
     
Europe 2024
 •   Plastics Recycling World Expo
     
North America 2024
 •   PRS Asia 2024
 •   PRS India 2024

mehr...


Fachartikel:

Rezyklate direkt beim Spritzgießen und der Extrusion prüfen
NIR-Verfahren zur Inline-Kontrolle von Recycling-kunststoffen
Kunststoffe 2/2024

 

mehr ...


Pressemitteilungen:

Inline-Farbkalibrierung auf Kunststoffrezyklate
(Inline-Farbmesssysteme)

 
Testbericht zur Inline-Farbmessung an Rezyklaten
(Inline-Farbmesssystem)

mehr ...


Whitepaper:

Sensorsysteme zur Rezyklat-Kontrolle in der Kunststoffindustrie fürs Labor und Inline
Kontrolle der Kunststoffart von Rezyklaten und Neuware mit Hilfe der NIR-Technologie

mehr ...


Applikationen:

Detektion von Dellen und Beulen auf Metall-Stanzbändern
(N° 801)
Unterscheidung von Leder-, Textil- und Kunststoff- Interieurkomponenten
(N° 802)
Farbmessung von Kunststoffdeckeln
(N° 803)

mehr...


WAS IST ...
... Oberflächenspannung?
... Ölverdunstung?
... Ölschichtdickenmessung?

mehr...


Software-Neuheiten:

SPECTRO3-MSM-DIG-Scope V1.5 (2021.10.20)
V1.5.2

mehr...



FIND US ON ....

Facebook X (Twitter) Instagram Youtube in

 








TOP