Praktische Beispiele aus dem industriellen Einsatz
L-LAS-RL-20-W
1) Sprache auswählen:
|
石板的高度检测 在用输送带输送石板期间应检测石板的厚度。首先，输送带造成的高度波动可以忽略不计，因此可以将之作为参考值。 Stone plate thickness control The thickness of stone plates should be measured. At this, the stone plates will be transported on a conveyor belt with a negligible movement in height, thus it can be used as a reference. |
|
|||
|
检测一种面料由粗到细的过渡 应能在一块织物面料上检测出由粗到细的过渡位置。 Edge position detection on fabric The position of the changeover from rough to fine on a textile should be detected. |
|
|||
|
非对称螺旋弹簧的摆放姿势检测 用于检测非对称弹簧的摆放姿势是否正确。 Attitude control of an asymmetric spiral spring The attitude of an asymmetric suppressed spring should be controlled. |
|
|||
|
织物边缘检测 检测图示网状织物的边缘，该应用中，织物边缘偏差需控制在20mm以内，选用的传感器精度为±2mm。 Edge detection of a fabric The lateral position of a wide-meshed fabric should be controlled in a range of 20mm. At this, the necessary accuracy should be ±2mm and the bandwidth of the analogue output signal has to be a few Hz. |
|
|||
|
汽车行业冲压板层数检测 此应用中，机械手将冲压好的板材一片片吸起并送至下一个工位。而有时会误同时吸起2片甚至多片板材，此时SI传感器会给出报警信号。 Double sheet control of stamping parts in the automotive industry During the handling process of stamped metal parts it happens, that instead of one part two or more parts will be sucked up from a robot. |
|
|||
|
橡胶密封垫定位 SI传感器在此应用中用于对橡胶密封垫的精准定位。 Positioning of a rubber seal component A rubber gasket should be exact positioned. |
|
|||
|
双层金属板检测 在此应用中，机械手从堆积的金属板材中，将金属板一片片的吸起并移到另外一个工位。在此过程中，有可能会有2片金属板被一起吸起移走的情况，这种情况必须被避免。SI传感器可以从侧面来检测板厚，从而分辨该金属板是单层还是多层。 Double sheet control Metal plates should be removed from a stack with a robot. The robot sucks the metal sheets one by one and it should be avoided for safety reasons to move two metal sheets simultaneously. A sensor should detect double sheet not from the top but from the side. Furthermore, the system should be adapted automatically after a change of the type of metal sheet (different thickness or different metal). |
|
|||
|
金属板上的雕刻标记 用于检测金属材料表面的雕刻标记，该标记用于定位X,Y轴，确定金属材料卷折方向。 Detection of an engraving mark on a metal plate An engraving mark which is used for positioning in x-, y- and roll-direction has to be detected. |
|
|||
|
保险纸水印标记识别 在印刷过程中在线识别保险纸上的水印印记。 Detection of a reference water mark on safety paper The position of a reference water mark must be inline detected. During the printing process it is necessary to synchronize the consecutive registers to the reference water mark. |
|
|||
|
汽车内饰行业人造革&真皮皮革颜色-光泽度检测 在汽车内饰行业有些皮革材料看起来非常相似。为了区别他们必须同时对其颜色和光泽度进行检测。 Color-gloss differentiation of leather and leather imitations in the automotive interior field In the automotive interior field the different materials looks sometimes very similar. For a proper differentiation of the different products color-gloss detection should be used. |
|
|||
|
汽车内饰行业人造革和皮革的分辨 在汽车内饰的皮革检测中，有些皮料表面颜色及光洁度几乎完全一致，即使是最好的颜色传感器都无法分辨。此时，为了分辨出人造革和真皮皮革，我们需要引入另外一种传感器，对皮料的表面结构/纹路进行检测，从而有效的分辨出人造革及真皮皮革。 Differentiation of leather and leather imitations in the automotive interior field Sometimes a color differentiation between interior materials with exactly the same color and the same gloss factor is not possible, even with the best color sensor. Thus another sensor must close this gap. Indeed the different materials may have the same color and the same gloss, but a different structure as shown in the photos. |
|
|||
|
砂带边缘控制 各种砂带都会加边。此砂边位于砂带砂面和侧面之间。此边颜色一般比砂带砂面颜色浅但是比侧面颜色深。根据此色差，这条砂边的颜色及位置可以有效的被颜色传感器识别。 Control of margined abrasive belts Different sanding belts are equipped with a margin and this margin has to be controlled. The margin can be present on the sanding side of the abrasive belt or on the rear side. Furthermore the margin can be darker than the rear side but mostly it is brighter than the sanding surface. Nevertheless there is a sufficient difference in contrast between the margin and the rear side or the sanding side. |
|
|||
|
金属管生产过程中的长度检测 在金属管生产过程中需检测裁断后的管子长度，其精度必须被控制在十分之一毫米内。 Measurement of length of metal collapsible tubes during the production process During the production of metal tubes, the length of the tubes must be controlled, because of the previous cutting process of the tubes. The accuracy of the metal tubes should be in a range of a tenth of a millimeter. |
|
|||
|
木材加工业和造纸行业中传送带的横向位置控制 木材加工业（生产中纤板）和造纸行业中需要使用特殊的传送带。带子横向位置需控制在±0.2mm范围内，纵向位置可在±2mm间变化。传送带材料为不锈钢或塑料织物。 Lateral position control of conveyor belts in the wood and paper industry In the wood industry (during the production e.g. of MDFs = medium density fiberboards) as well as in the paper industry, special conveyor belts are in use. The lateral position of the band material must be hold in a range of ±0.2mm, whereas the vertical position can change in the range of ±2mm. The material of the conveyor belt is either stainless steel or plastic fabric. |
|
|||
|
防伪纸上珠光色带的颜色检测 传感器需对珠光色带上各颜色的位置及质量进行检测。 Detection of pearlescent color strips on security papers The position as well as the quality of pearlescent multi color strips on security paper should be controlled. |
|
TOP