Praktische Beispiele aus dem industriellen Einsatz
L-LAS-RL-20-W
1) Sprache auswählen:
|
Stone plate thickness control The thickness of stone plates should be measured. At this, the stone plates will be transported on a conveyor belt with a negligible movement in height, thus it can be used as a reference. |
|
|||
|
Edge position detection on fabric The position of the changeover from rough to fine on a textile should be detected. |
|
|||
|
Attitude control of an asymmetric spiral spring The attitude of an asymmetric suppressed spring should be controlled. |
|
|||
|
Edge detection of a fabric The lateral position of a wide-meshed fabric should be controlled in a range of 20mm. At this, the necessary accuracy should be ±2mm and the bandwidth of the analogue output signal has to be a few Hz. |
|
|||
|
Double sheet control of stamping parts in the automotive industry During the handling process of stamped metal parts it happens, that instead of one part two or more parts will be sucked up from a robot. |
|
|||
|
Positioning of a rubber seal component A rubber gasket should be exact positioned. |
|
|||
|
Dubbelarkskontroll En robot ska plocka metallplåtar. Den ska bara ta en plåt åt gången av bl.a. säkerhetsskäl. En sensor kontrollerar detta från sidan och systemet ska automatiskt justeras efter typ av metallplåt så som tjocklek och vilken metall det är. Double sheet control Metal plates should be removed from a stack with a robot. The robot sucks the metal sheets one by one and it should be avoided for safety reasons to move two metal sheets simultaneously. A sensor should detect double sheet not from the top but from the side. Furthermore, the system should be adapted automatically after a change of the type of metal sheet (different thickness or different metal). |
|
|||
|
Detektion av positioneringsmärke på metallplatta Ett ingraverat märke på metallplatta ska detekteras för att positionera plattan korrekt. Detection of an engraving mark on a metal plate An engraving mark which is used for positioning in x-, y- and roll-direction has to be detected. |
|
|||
|
Positionering av vattenstämpel på säkerhetspapper Kontinuerlig positionering av markeringar i form av vattenstämplar ska göras i produktionen av säkerhetspapper. Detta för att synkronisera med efterföljande processteg i tillverkningen. Detection of a reference water mark on safety paper The position of a reference water mark must be inline detected. During the printing process it is necessary to synchronize the consecutive registers to the reference water mark. |
|
|||
|
Color-gloss differentiation of leather and leather imitations in the automotive interior field In the automotive interior field the different materials looks sometimes very similar. For a proper differentiation of the different products color-gloss detection should be used. |
|
|||
|
Differentiation of leather and leather imitations in the automotive interior field Sometimes a color differentiation between interior materials with exactly the same color and the same gloss factor is not possible, even with the best color sensor. Thus another sensor must close this gap. Indeed the different materials may have the same color and the same gloss, but a different structure as shown in the photos. |
|
|||
|
Kontroll av kantlinje på slipband På slipband finns en linje vid ytterkanten av slipytan. Denna linje ska detekteras och den skiljer sig i färg mot slipytan och det rena bandet. Oftast är den mörkare än bandet men ljusare än slipytan vilket gör att givaren kan detektera den smala linjen. Control of margined abrasive belts Different sanding belts are equipped with a margin and this margin has to be controlled. The margin can be present on the sanding side of the abrasive belt or on the rear side. Furthermore the margin can be darker than the rear side but mostly it is brighter than the sanding surface. Nevertheless there is a sufficient difference in contrast between the margin and the rear side or the sanding side. |
|
|||
|
Längdmätning av metallrör med hög noggrannhet Efter kapning av metallrör ska deras längd mätas. Längdtoleransen ska vara inom en tiondels millimeter. Measurement of length of metal collapsible tubes during the production process During the production of metal tubes, the length of the tubes must be controlled, because of the previous cutting process of the tubes. The accuracy of the metal tubes should be in a range of a tenth of a millimeter. |
|
|||
|
Övervakning av sidoförskjutning av transportband - kantstyrning Inom träindustrin (tillverkning av MDF-skivor) och pappersindustrin används speciella transportband av rostfritt stål eller konstfiberband. Kontroll av bandets läge i sida ska göras med noggrannhet av ±0,2 mm medan bandets läge i höjdled kan variera ±2 mm. Lateral position control of conveyor belts in the wood and paper industry In the wood industry (during the production e.g. of MDFs = medium density fiberboards) as well as in the paper industry, special conveyor belts are in use. The lateral position of the band material must be hold in a range of ±0.2mm, whereas the vertical position can change in the range of ±2mm. The material of the conveyor belt is either stainless steel or plastic fabric. |
|
|||
|
Kontroll av pärlglanspigment på säkerhetspapper Under tillverkningen av säkerhetspapper ska korrekt läge och tjocklek på trycket av pärlglanspigmentet kontrolleras. Detection of pearlescent color strips on security papers The position as well as the quality of pearlescent multi color strips on security paper should be controlled. |
|
TOP