Практические примеры применения в промышленной сфере
RLS-GD-15/60°
1) Выбрать язык:
|
Front side – backside differentiation of paper web The backside of yellow and white paper web should be differentiated from the respective front side. |
|
|||
|
Gloss measurement of transparent plastic films The gloss factor of different transparent plastic films should be measured on both sides. |
|
|||
|
Glansmåling af eloxierede ledeskinner Glansen på forskellige aluminiumsledeskinner skal måles inline. Gloss measurement of anodized guide rails The gloss of anodized aluminum guide rails should be inline measured. |
|
|||
|
Glansmåling på semitransparente plastfolier Glansgraden skal måles på lysgennemtrængelig plastfolie in-line. Gloss measurement of translucent plastic films The gloss level of semi-transparent plastic films should be inline measured. |
|
|||
|
Glansmåling på farve-coated stof Glansgraden på -farvecoated stof skal måles. Gloss measurement on coated textiles The gloss of fabrics will be influenced from a special coating and the task should be an inline measurement of the gloss value. |
|
|||
|
Glansmåling på polerede granitplader Glansen skal måles på polerede granitplader. Gloss measurement on polished slabs The gloss of polished slabs should be measured. |
|
|||
|
Glansmåling på grundfarven på en vindmøllevinge Glansfaktoren på en grundfarven på en vindmøllevinge, skal måles berøringsløst. Til dette formål monteres en glanssensor på en robotarm, som holdes i en afstand af 15 mm over fladen. Samtidigt bevæges vindmøllevingen horisontalt under glanssensoren. Normalt vil værdien skulle ligge på under 5 for at sikre en god vedhæftning for det næste lag. Gloss measurement of the primer surface on a vane The gloss factor of the primer surface of vanes from wind turbines should be measured contactless. At this, the gloss sensor is mounted on a robot and will be moved vertically to make sure, that the distance to the primer surface of the vane remains approximately at 15mm, simultaneously the vane will be moved horizontally so that the gloss factor can be measured along the long axis of the vane. Normally the gloss factor of the primer surface should be lower than 5 in order to guarantee that the following coating get a fix compounding to the primer surface. |
|
|||
|
Glansmåling på glasoverfladen på solcellepaneler Glansfaktoren for beskyttelsesglas på solceller, skal måles under produktionen. Gloss measurement of the glass surface of a photo voltaic panel The gloss factor of the glass cover of a photo voltaic panel should be measured during the production. |
|
|||
|
Skelne mellem for- og bagside på lyddæmpningstæppe Fronten skal skelnes fra bagsiden på et lysdæmpningstæppe. Differentiation of front side and back side from a sound damping carpet The front side should be distinguished from the back side of a sound damping carpet. |
|
|||
|
Skelne mellem kunstlæder To forskellige kunstlæder varianter skal skelnes og glansfaktoren skal gemmes som dokumentation med en glanssensor. Differentiation of leather imitations Two black leather imitations should be differentiated and the gloss factor should be documented with a gloss measurement device. |
|
|||
|
Glansmåling inline efter lakering af døre Umiddelbart efter lakering af døre, skal glansfaktoren kontrolleres. Tests har vist at mængden af lak, som tilføres døren, influerer på glansfaktoren, da denne viser ru overflade, hvis der ikke er nok lak tilstede. Gloss inline measurement after the varnish of doors Immediately after the varnish of the doors the gloss factor should be controlled. Tests have shown that the amount of varnish, which will be sprayed onto the door surface, influences the gloss factor. If not enough varnish is used the surface becomes rough. |
|
|||
|
Inline glansmåling på slibebånd Glansfaktoren er en vigitg parameter for overfladekvaliteten, ruheden, på et slibebånd. Derfor anvendes en inline sensor til kontrollen af slibebåndene. Inline gloss measurement on abrasive belts The gloss factor is a significant parameter for the surface quality, the roughness, of an abrasive belt. Thus a gloss measurement inline sensor should be used for quality control of the abrasive surface. |
|
|||
|
Inline glansmåling på plastfilm og laminerede plader Under produktionen af plastfilm og laminerede plader, skal glansfaktoren måles. Inline gloss measurement of plastic films and laminated plates During the production of plastic films as well as of laminated plates the gloss factor should be measured. |
|
|||
|
Inline glanskontrol I møbelindustrien I fremstillingsprocessen, skal dørene lige efter maling kontrolleres for mængde af maling/glans. Inline gloss control in the furniture industry During the manufacturing process of doors just after the painting line the amount of color must be controlled. |
|
|||
|
Aftastning af blanke områder på materede glasplader Under produktionen af materede glasplader, skal overfladen kontrolleres ekstra for små blanke pletter. De blanke pletter som skal aftastes starter fra ca. 3 mm. Detection of glossy regions on a matt-finished glass plate During the production of matt-finished glass plates the matt-finished surface must be controlled particularly with regard to small glossy spot. The glossy domains which should be detected are starting with a diameter of approximately 3 mm. |
|
